Surface Modification Of Fibers Research Articles

Influence of Interfacial Interaction and Composition on Fracture Toughness and Impact Properties of Carbon Fiber-Reinforced Polyethersulfone.

In this study, the interlaminar fracture toughness and impact strength of polyethersulfone reinforced with continuous carbon fibers were studied. Interlaminar fracture toughness tests were performed using the double cantilever beam method. It was shown that surface modification using the thermal oxidation method of the carbon fibers can strongly increase the interlaminar fracture toughness of the obtained composites. Thus, the maximum value reached 1.72 kJ/m2, which was 40% higher than the fracture toughness of the composites reinforced with initial carbon fibers. Moreover, fractographic analysis using a scanning electron microscope allowed us to highlight the main reasons for the dependence of fracture toughness on fiber content and surface modification conditions of the carbon fibers. It was shown that the main factor that allowed for an increase in fracture toughness was the enhanced interfacial interaction between the fibers and polymer matrix. Additionally, it was found that expectedly, there was a good correlation between interlaminar fracture toughness and interlaminar shear strength results. However, a negative influence of surface modification on the impact properties of composites was found. Such behavior occurred because of higher structural stability and lower exposure to delamination in multiple layers of the composites reinforced with the modified carbon fibers. It was found that impact energy reached ~150 kJ/m2 for the polyethersulfone-based composites reinforced with initial fibers, while the composites reinforced with modified carbon fibers showed impact energy values of only ~80 kJ/m2. Nevertheless, surface modification of carbon fibers using the thermal oxidation method can be an effective method for improving the performance properties of polyethersulfone-based composite materials.

Plant fiber-reinforced green composite: A review on surface modification, properties, fabrications and applications

Plastic pollution has become a persistent challenge globally. The extensive production of disposable plastics overwhelms the world's ability to cope with. These non-biodegradable plastics accumulating in landfills, rivers, and seas cause severe damage to wildlife and the environment. The utilization of biopolymer is a possible alternative to petroleum-based plastics. Polybutylene succinate (PBS), polyhydroxyalkanoates (PHA), polylactic acid (PLA), poly(ε-caprolactone) (PCL), cellulose, chitin, and thermoplastic starch are mostly used biopolymers with promising properties. There are challenges too. Properties including brittleness, low thermal stability, low strength, and poor chemical barrier properties are the challenges to replacing plastics material. Reinforcing natural fibers as an alternative to non-biodegradable synthetic fiber with biopolymer matrices improves the properties of the material significantly. Flax, kenaf, jute, ramie, and hemp are a few agro-based fibers that are generally reinforced with biopolymer matrices. These composites are known as green composites. In order to create an interfacial bond between hydrophilic fiber and hydrophobic biopolymer surface modification of natural fiber is needed. There are many physical and chemical methods of surface medication which enhance roughness, wettability as well as hydrophilicity, lowers moisture absorption, improve the interfacial bond, and also enhance the tensile properties of natural fiber. The review is on the classification of biopolymers, natural fibers and their properties as well as the surface modification techniques for plant fibers. Moreover, the fabrication, mechanical and chemical properties including biodegradation of different green composites and the application of green composites, are also discussed here.

Deposition of thin films on basalt fibers surface by atmospheric pressure plasma with different siloxane precursors

In this study, surface modification of basalt fibers (BFs) utilizing atmospheric pressure plasma deposition was carried out. Using this one-step deposition approach, three siloxane precursors with different structures including methyltrimethoxysilane (MTMS), hexamethyldisiloxane (HMDSO), and tetramethoxysilane (TMOS) were deposited on BFs surface, respectively. The physicochemical properties of the thin films from three different siloxane compounds are elucidated. In comparison with MTMS-coated sample, HMDSO-coated and TMOS-coated BFs surfaces feature an improved thermal insulation performance. The results demonstrate that atmospheric pressure plasma deposition is an efficient approach to modify flexible materials surface with improved thermal insulation. Moreover, it provides a reference to decide which precursor type is preferred for certain applications.

Flexural Properties and Failure Mechanisms of Short-Carbon-Fiber-Reinforced Polylactic Acid Composite Modified with MXene and GO.

Recently, short-fiber-reinforced thermoplastic composites (SFRTPCs) have been playing a more and more crucial role in the application of automotive interior materials due to their advantages of low density and environmental resistance properties. However, their relevant mechanical properties need to be optimized. Previous investigations revealed that the surface modification of fibers is useful to improve their mechanical properties. In this work, carbon fiber (CF)-reinforced polylactic acid (PLA) composites modified with MXene and graphene oxide (GO) were prepared by twin-screw extrusion and injection molding methods. Short CF was firstly modified with polyetherimide (PEI), then different weight ratios of MXene-GO (1:1) were subsequently modified on PEI-CF. Finally, the flexural properties and failure mechanisms were analyzed. The results showed that MXene-GO was successfully coated on CF surface, and the flexural strength and modulus of CF-PEI-MXene-GO-reinforced PLA (CF-PEI-MG/PLA) composite were improved compared to that of CF/PLA composite. In addition, the fracture sections of the composites were flat and white, and the fibers bonded well with PLA for CF-PEI-0.1MG/PLA composite compared to CF/PLA composite. The present study could provide a reference for further improving the mechanical performance of PLA-related composites.

Fabrication of highly conductive polyester fabrics using single-wall carbon nanotubes inks for EMI shielding

Abstract We have fabricated single-wall carbon nanotube (SWCNT)-coated electrically conductive polyester fabric using a low-temperature (LT) dip-and-dry method. Polyester fibers are suitable for industrial applications because of their higher heat resistance. We focused on the surface modification of polyester fibers using N,N-dimethyl-formamide solvent and then improved the adhesion of the SWCNT to polyester fibers. The low sheet resistance of 4.3 ± 0.3 Ω sq−1 was achieved while maintaining the intrinsic flexibility and durability of polyester fabrics by using the LT dip-and-dry method. Moreover, we demonstrated the electromagnetic interference (EMI) shielding using the fabricated electrically conductive polyester fabric. The EMI shielding effectiveness (SE) was measured in the frequency ranges of 8–12 GHz using waveguides and a vector network analyzer. The measured SE of the fabricated electrically conductive polyester fabric was about −34 dB and fulfilled the requirement for practical EMI shielding.

Surface modification of Luffa and Maize fibers by using alkali medium

Agricultural biomass is a well-known renewable resource that has a high rate of recycling. Two of them are luffa sponge and corn husk/maize fibers. Luffa sponge may be effectively used to reinforce lightweight composite constructions because of its polypore structure. For this race, maize fiber is also appropriate. Surface modifications for both of the fibers are needed for increasing mechanical strength with higher interfacial bonding with the matrix materials of composite manufacturing. This investigation involved treating both materials with 5 g/L, 10 g/L, and 15 g/L of NaOH in order to describe the alterations occurring on their physio-chemical characteristics. The therapy lasted 60 min and was administered at 90 °C. Following that, acetic acid was used to neutralize the samples. The ASTM D1445 technique was used to measure the bundle fibers' breaking force and elongation, and the ASTM D570 procedures were used in order to determine the water absorption variation % in the treated samples. The FTIR test and SEM examination revealed the contaminants that were eliminated from the surface of Luffa and Maize fibers. The test findings demonstrated improved modification behaviors for the 15 g m/L treated fibers, which had an elongation percentage of 3.02% and an equivalent breaking force of 5.12 kg for the Luffa fiber and 5.72 kg for the maize fiber. Natural contaminants were eliminated as a result of variations in functional group intensity shown in the FTIR pictures. However, SEM pictures showed that the surface smoothed out for samples treated with 15 g per liter of NaOH, which may be the cause of the fiber's brittle interlocking with the matrix components. Moreover, water absorbency rose by over 300% compared to the untreated fibers. In summary, samples treated with 10 g/L NaOH might serve as superior reinforced materials of composite for both types of fibers.

Bamboo fiber reinforced poly (acrylonitrile-styrene-acrylic)/chlorinated polyethylene via compabilization

In the quest to enhance the performance of natural fiber-reinforced polymer composites, achieving optimal dispersion of fiber materials within a polymeric matrix has been identified as a key strategy. Traditional approaches, such as the surface modification of natural fibers, often necessitate the use of additional synthetic chemical processes, presenting a significant challenge. In this work, taking poly (acrylonitrile–styrene–acrylic) (ASA) and bamboo fiber (BF) as a model system, we attempt to use the elastomer-chlorinated polyethylene (CPE) as a compatibilizer to tailor the mechanical properties of ASA/CPE/BF ternary composites. It was found that increasing CPE content contributed to more remarkable reinforcing efficiency, where composite with 15 phr CPE exhibited a nearly four-fold increase in reinforcing efficiency of tensile strength (20 %) compared with that of composite system without CPE (4.1 %). Such improvement was ascribed to the compatibilizing effect exerted by CPE, which prevented the aggregation of BF within polymeric matrix. Surface properties suggested the stronger interface between CPE and BF compared to that between ASA and BF and thereby contributed to the compabilizing effect. Since no chemical process was involved, it is suggested that the introduction of elastomer to be a universal, green and sustainable approach to achieve the reinforcement.

Research on surface modification of polypropylene fiber and its application evaluation in oil well cement

In order to improve the compatibility and dispersibility of polypropylene fiber (PPF) in oil well cement and enhance the mechanical properties of cementing cement sheath, the surface modification of PPF was carried out in this study. After surface impurity removal of PPF, reaction of catechol with polyamines, and subsequent treatment with γ- aminopropyltriethoxysilane (KH-550) and Ethyl orthosilicate (TEOS), modified polypropylene fiber (MPF) was obtained. The MPF was characterized and analyzed using FTIR, XPS, SEM, and EDS, showing a transformation in the surface properties of the fibers. The most significant change was that the contact angle between MPF and water decreased from 123.87 ° to 46.32 °, marking the successful transition of the fiber from hydrophobicity to hydrophilicity. Image analysis showed that the dispersion of MPF improved significantly. The dispersion coefficient of MPF in water and cement stone was increased by 86.90% and 14.48% compared with PPF, respectively. The effect of MPF on mechanical properties of oil well cement stone was studied. The comparative analysis results showed that MPF can significantly improve the flexural and compressive strength of the cement matrix. The flexural and compressive strength of cement stone mixed with MPF were increased by 10.25% and 6.43%, respectively, compared to cement stone mixed with PPF. SEM, MIP, and fiber single fiber pull-out experiments showed that the porosity of cement stone added with MPF was lower, the rough surface structure of MPF enhanced the bonding between fibers and cement stone, and the bridging effect of fibers in cement stone ultimately improved the mechanical properties of oil well cement stone.

Mechanical and ballistic performance of ramie fiber-reinforced polymer composites: A review

Natural fiber composites (NFCs) have seen an increased innovation and research activities due to their strength, environmental impact, and low cost. NFCs are used in aerospace, construction, leisure, packing, sport, and automotive industries. One such NFC, ramie fiber-reinforced composite has gained more importance due to its high mechanical strength, stiffness, and easy availability to all other natural fibers. In this review, an insight of the research works focusing on ramie fiber, and its reinforced polymer composite has been summarized. Factors such as fiber content, surface treatment, manufacturing techniques, and coupling agents influencing the mechanical properties (tensile, flexural, and impact) have been summarized. It is evident that the surface modification of ramie fiber through chemical treatment and the addition of coupling agents directly impact the mechanical properties of the composite. Furthermore, the usage of ramie fiber composite is still inadequate due to its poor fire and moisture-resistant properties.

A promising method for promoting interfacial adhesion of aramid/rubber composite using atmospheric pressure plasma surface modification

AbstractToday, aramid fibers are well known as a high‐performance and ideal material for reinforcement purposes in rubber product manufacturing including hoses, tires, cables, and conveyors composites. However, surface modification of aramid fiber is necessary to solve poor interfacial adhesion between aramid fibers and the rubber matrix. Accordingly, in the present study, the effect of the surface modification of aramid fibers using atmospheric pressure plasma treatment with different precursors on adhesion to the rubber matrix was investigated. For that, the plasma coating was conducted using argon as the main working gas, and toluene, acetonitrile, tetraethyl orthosilicate (TEOS), and hexamethyldisiloxane (HMDSO) as liquid precursors. The physical–chemical characterization of the layer confirmed the successful deposition of amorphous carbon, amorphous nitride‐carbon, SiO2, and Polydimethylsiloxane (PDMS)‐like coating layers on the surface of aramid fibers by using toluene, acetonitrile, TEOS, and HMDSO as precursors, respectively. Overall, the result showed that the plasma surface modifications with acetonitrile precursor leads to the increase in interfacial adhesion of aramid/rubber composite, while retaining the tensile strength, and flame resistance properties of aramid as original fibers. Notably, the results of this study confirm the potential use of atmospheric pressure plasma for surface modification of aramid yarn to produce functional aramid for use in rubber composites.Highlights The plasma‐coated aramid using HMDSO, TEOS, toluene, and acetonitrile precursors was prepared; and its effect on the tensile properties of aramid fiber as well as interfacial adhesion between aramid/rubber composite was investigated. The positive effect of atmospheric pressure plasma coating using HMDSO precursor on the tensile properties of aramid fiber was revealed. The positive effect of atmospheric pressure plasma coating using toluene and acetonitrile on the interfacial adhesion between aramid/rubber composite was revealed. The positive effect of atmospheric pressure plasma coating using TEOS precursor on the flam resistance property of aramid fiber was revealed. This study provides valuable insights into the effect of the different plasma‐coated organosilicon and hydrocarbon precursors on the interfacial adhesion between aramid/rubber composite.

Decoration with electronegative 2D materials based on chemical transition layers on CFR-PEEK implants for promoting osteogenesis

Due to the unique lamellar structures, physicochemical and biological properties, electronegative two-dimensional (2D) materials have been explored for surface modification of carbon fibers reinforced polyetheretherketone (CFR-PEEK) composite. Deposition of electronegative 2D materials based on a porous surface created by concentrated H2SO4 has been studied to promote osteogenesis of CFR-PEEK. Generally, a porous layer will be pre-built on CFR-PEEK through severe corrosion of concentrated sulfuric acid to help the loading of 2D materials. However, the severe corrosion will greatly reduce surface mechanical strength, especially wear resistance and hardness, which increases the risk of collapse or even peeling of the bioactive coating by external force. Herein, instead of the severe corrosion, a mild corrosion by concentrated HNO3 was applied to modify the surface of CFR-PEEK to pre-create a dense transition layer for the further surface decoration of electronegative 2D materials (graphene oxide (GO) and black phosphorus (BP), representatively). The results indicated that hardness and wear resistance of the dense transition layer were markedly higher than those of the porous layer. Although GO and BP can be both loaded on these two transition layers, –SO3H on the porous transition layer showed moderate cytotoxicity, while –NO2 on the dense transition layer showed good cytocompatibility. The dense transition layer displayed higher mineralized deposition in vitro and new bone formation rate in vivo than the porous transition layer, moreover, GO and BP coatings improved osteogenesis. This work offers inspirations for the construction of electronegative 2D material coating on CFR-PEEK based on chemical transition layers.

Surface Modification of Flax Fibers with TMCTS-Based PECVD for Improved Thermo-Mechanical Properties of PLA/Flax Fiber Composites.

Significant progress has been made in recent years in the use of atmospheric pressure plasma techniques for surface modification. This research focused on the beneficial effects of these processes on natural by-products, specifically those involving natural fiber-based materials. The study explored the deposition of hydrophobic organosilicon-like thin films onto flax fibres through plasma-enhanced chemical vapour deposition (PECVD), using tetramethylcyclotetrasiloxane (TMCTS) as the precursor. After the successful deposition of hydrophobic organosilicon-like thin films onto the flax fibres, polylactic acid (PLA) composite materials were fabricated. This fabrication process sets the stage for an in-depth analysis of the modified materials. Subsequently, these flax fabrics were subjected to meticulous characterization through scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. The results demonstrated successful TMCTS deposition on the surface which led to a complete hydrophobization of the flax fibers. Mechanical tests of the PLA/flax fibre composites revealed a significant improvement in load transfer and interfacial compatibility following the surface modification of the flax fibres. This improvement was attributed to the enhanced adhesion between the modified fibres and the PLA matrix. The findings highlight the potential of TMCTS-based PECVD as a practical surface modification technique, effectively enhancing the mechanical properties of PLA/flax fibre composites. These developments open exciting possibilities for sustainable and high-performance composite materials in various industries.

A universal strategy for rapid and scalable surface modification of ultra high molecular weight polyethylene fiber

The high performance UHMWPE fiber usually demonstrates extremely poor surface adhesion with resin matrix. Therefore, improving the interfacial adhesion property becomes one of the toughest challenges faced by UHMWPE fibers. In this study, a simple and universal surface welding strategy is promoted to effectively modifying UHMWPE fiber with improved surface adhesion in a short time. The surface welding manufacturing approach is realized by the controllable Joule heating generated from the high contact resistance and rapid thermal response of the conductive nano-material layer coated on UHMWPE surface, which can locally melt the UHMWPE fiber surface and weld the nano materials on UHMWE with a strong and robust mechanical bonding. Since the whole welding process is simple and lasts only for a few seconds, it can be easily applied to the current industrial UHMWPE fiber and fabric manufacturing, enabling a continuous, fast, efficiency and scalable roll-to-roll UHMWPE surface modification process.

Highly sensitive fiber-optic chemical pH sensor based on surface modification of optical fiber with ZnCdSe/ZnS quantum dots

The pH value plays a vital role in many biological and chemical reactions. In this work, the fiber-optic chemical pH sensors were fabricated based on carboxyl ZnCdSe/ZnS quantum dots (QDs) and tapered optical fiber. The photoluminescence (PL) intensity of QDs is pH-dependence because protonation and deprotonation can affect the process of electron-hole recombination. The evanescent wave of tapered optical fiber was used as excitation source in the process of PL. To obtain higher sensitivity, the end faces of fiber were optimized for cone region. By lengthening the cone region and shrinking the end diameter of optical fiber, evanescent wave was enhanced and the excitation times of QDs were increased, which improved the PL intensity and the sensitivity of the sensor. The sensitivity of sensor can reach as high as 0.139/pH in the range of pH 6.00–9.01. The surface functional modification was adopted to prepare sensing films. The carboxyl groups on the QDs ligands are chemically bonded to the fiber surface, which is good for response time (40 s) and stability (decreased 0.9 % for 5 min). These results demonstrated that ZnCdSe/ZnS QDs-based fiber-optic chemical pH sensors are promising approach in rapid and precise pH detection.

Research progress on the surface modification of carbon fiber.

Carbon fiber (CF) has high strength, high modulus, and excellent high-temperature resistance and chemical stability; therefore, it is used in diverse fields. However, due to the lack of active functional groups on the surface of CF and surface defects generated during the preparation of CF, the wettability of the fiber surface is poor, which seriously affects the interface performance between the fiber and a resin matrix. In recent years, extensive research has been conducted on the surface modification of CF. In this review, studies on the surface modification of CF are summarized, including the various methods utilized, such as dry modification, wet modification, and nanomodification, as well as their current application status. As interest in this material increases, high-performance CFs will likely play an important role in many fields in the future.

Chemically tailored molecular surface modification of bamboo pulp fibers for manipulating the electret performance of electret filter media

The surface chemical composition of materials is essential for regulating their charge trapping and storage capabilities, which directly affect their electret performance. Although chemical modification of materials to alter electret performance has been investigated, the mechanism through which electret properties are regulated more systematically via chemical customization has not been elucidated in detail. Herein, p-phenylenediamine, benzidine and 4,4′-diaminotriphenyl, which have different conjugated strength functional groups, were selected to chemically tailor the surface of bamboo pulp fibers to regulate the electret properties and elucidate the regulatory mechanism more systematically. The results showed that the charge trapping and storage properties of materials could be regulated by introducing functional groups with different conjugated strengths to their surfaces, realizing the regulation of the electret properties. Moreover, the charge trapping and storage ability could be tailored more specifically by regulating the number of functional groups. By chemical customization to provide electrostatic effects to the materials, the purification time was reduced by approximately 45 %–52 %. More importantly, a relatively systematic mechanism was proposed to elucidate the effect of the conjugate group strength on the charge trapping and charge storage properties of the material. These findings will provide guidance for the investigation of chemical modifications to regulate the electret performance of materials.

Aging Effect of Plasma-Treated Carbon Fiber Surface: From an Engineering Point

Dielectric barrier discharge (DBD) plasma surface modification has certain aging effect. This article studies the aging effect of plasma (DBD) on the surface modification of carbon fibers. The test results show that plasma (DBD) treatment reduces the impurity particles on the surface of carbon fibers and makes the surface texture coarser. In addition, there is no significant change. After plasma (DBD) treatment, the content of C–O–C, C–O and C=O on the surface of carbon fibers increased from 3.20%, 7.76% and 1.64% to 7.06%, 21.50 and 6.08%, respectively. This is due to the high-energy particle bombardment of the fiber surface, which forms activated carbon atoms on the surface. The free electrons of these activated carbon atoms combine with ionized oxygen in the air. However, with the passage of time, the content of C–O–C, C–O and C=O gradually decreases to 3.31%, 8.57% and 1.77%, respectively. This is because some functional groups formed on the treated carbon fiber surface are not firmly bound, and some of these functional groups containing O2 groups will combine with surrounding substances through irreversible chemical oxidation reactions to produce CO2, which leaves the carbon fiber surface as a gas. The treated carbon fibers will immediately become hydrophilic, and the water contact angle decreases from 148.71° to 0°. With the passage of time, the water contact angle gradually increases to 118.16°, and the hydrophobicity recovers.

Extra thin sidelight-emitting polymer optical fiber narrow fabrics for UV structural adhesive joints: design, preparation and performance experiments

Ultraviolet (UV) bonding technology is widely used across industries. As the curing reaction is initiated via an external light source, the use of fast-curing structural UV acrylates has so far been limited to joint designs with at least one transparent joining part. By introducing a side-emitting polymer optical fiber textile into the adhesive layer, which acts as an embedded light source, the technology can be made accessible for applications with nontransparent substrates such as metals. This paper describes the development of extra thin polymer optical fiber narrow fabrics designed to enable curing of structural adhesive joints. Polymer optical fibers (warp) were combined with different low-titer polyester weft yarns in two fabric design types with different primary out-coupling mechanisms: undulation and surface modification of the polymer optical fibers. The effect of yarn properties, thread densities and weave on fabric quality, geometry and lateral light intensity of each type were investigated. Results showed that narrow fabric production within the tight geometric limits required is feasible. Fabrics manufactured with nontextured yarns at low titers and low weft densities exhibited the highest lateral light intensities for the surface modification type fabric. To compensate for intensity loss over fabric length, investigating light coupling from both sides is recommended for this fabric type. For the undulation type fabric, the lateral light intensity characteristics indicated that the high tenacity yarns are promising candidates for the fabrication of low sidelight attenuation fabrics through modulation of the weft density.

Timeliness of Cold Plasma Treatment on Surface Modification of Polylactic Acid Fibers

Polylactic acid (PLA) fiber is a promising material due to its biodegradability, excellent mechanical properties, and good biocompatibility. However, its surface is chemically inert and has poor interfacial compatibility with gases due to a low number of polar groups. To address this issue, this study utilized cold plasma and solution wet pretreatment with varying pH levels to modify the surface of PLA fibers. The use of solution wet pretreatment helped mitigate the negative effects of plasma treatment on the timeliness, which improved the long-term stability of the PLA fibers surface properties. These modifications increased the suitability of the material for various applications. The surface of PLA fibers was modified using cold plasma and wet pretreatment with pH solutions of varying degrees. The surface chemical composition and hydrophilicity of modified fibers remained relatively stable for up to 120 days. Conversely, unpretreated fibers reverted to their original chemically inert state after 14 days.

Surface modification of miscanthus fiber with hydrophobic silica aerogel for high performance bio-lightweight concrete

Bio-fiber reinforced cementitious material is now attracted widespread attention thanks to its low carbon footprint and its advantages in energy conservation in buildings. However, the main concerns of using large volume of bio-fibers in concrete is its high water absorption and the leaching of organic matter that is incompatible with cement. This study investigates a surface modification method of a bio-fiber (miscanthus) by using hydrophobic silica aerogel and further evaluates its mechanical and insulating performance in lightweight concrete and increase its compatibility with cement. X-ray diffraction, thermal gravimetry and calorimeter test were carried out to investigate the effect of hydrophobic miscanthus fibers on the microstructure of cement matrix. The results show silica aerogel modified miscanthus fiber enhances both the compressive and flexural strength, meanwhile significantly improving the insulating performance of concrete. The use of superhydrophobic aerogel particles reduces the sugar leached from miscanthus and the hydration heat peak is only slightly delayed with the incorporation of aerogel coated miscanthus fibers. The results of this study shed light on surface modifications of bio-fibers for applications in high performance construction materials.